Simple Questions and Short Answers

[Loewchen]

Why biters hatched from eggs despawn? Is there a way to ake them form a nest?

If they have no orders or cannot path to their destination they despawn after a while to save performance. Egg hatched enemies cannot create nests.

[kitters]

Why biters hatched from eggs despawn? Is there a way to ake them form a nest?

If they have no orders or cannot path to their destination they despawn after a while to save performance. Egg hatched enemies cannot create nests.

I remember reading somewhere, maybe wiki, that legendary biters from legendary eggs can potentially join expansion group and turn into legendary nest. Have anybody heard of it?

[Jap2.0]

Why biters hatched from eggs despawn? Is there a way to ake them form a nest?

If they have no orders or cannot path to their destination they despawn after a while to save performance. Egg hatched enemies cannot create nests.

I remember reading somewhere, maybe wiki, that legendary biters from legendary eggs can potentially join expansion group and turn into legendary nest. Have anybody heard of it?

I don't think wild nests can have quality. There is a bit of relevant discussion at 118842.

[kitters]

Is there a way to locate to tear down that old nasty radar that unnecessary occupies the needed frequency?
If not, it's gonna be a problem in the future.

[Jap2.0]

Is there a way to locate to tear down that old nasty radar that unnecessary occupies the needed frequency?
If not, it's gonna be a problem in the future.

Go to the map, ctrl + F radar will show you all radars on a given planet. That's as close as I know of.

[BlackHat]

Is there a way to make the ToolTip window pop up without having to hold the Shift key?

I took about a year long break from Factorio and just started again after updating to 2.1.9

The first thing I noticed was the ToolTip window below the mini-map was gone and I could not figure out why.
Figured it was a mod conflict as I had "edited" some of the .json from 2.0 to 2.1, then spent some time removing various mods to track down the problem. (That did not work)

TLDR, Googling, I found a Tips video reminding me to "dock" the ToolTip window under the mini-map.
BUT... I also saw I had to HOLD the SHIFT key to make it appear.

Hmm...... It has been a year (veggie brain) and I overwrote my 2.0 version so could not go back and check, but, was it always that way???
Is there some hotkey editing I can do, to make it so I DON'T need to hold down shift to see the tool tip?

Thanks
BlackHat

[Loewchen]

Is there a way to make the ToolTip window pop up without having to hold the Shift key?

In settings > Interface > Tooltip delay, change it to a lower value.

[BlackHat]

Is there a way to make the ToolTip window pop up without having to hold the Shift key?

In settings > Interface > Tooltip delay, change it to a lower value.

Already had it set to 0ms.

BUT... when I changed the "Entity Tool tip" below it, from Never to 0ms, it worked. I don't need to press SHIFT to make the tool tip to appear, just mousing over objects and items pops up the info tool tip.

Thanks,
BlackHat

[Tyrannosapien]

The editor mode won't select the entities I placed before I saved the editor session. Please tell me what I'm doing wrong, or if I broke it, how so I don't break it again.

I created a new editor session with all default game settings. After it loaded, I cleared all entities, changed to lab tiles, and then stamped a 250 square of copper. I created an array of miners and 3 similar blueprints in a new blueprint book. I ran the simulation for a bit confirming that the belts were complete, etc. Then I Save As a new file, then exited. I loaded up my current game and stamped a few copies of the BP, and then I decided to add some additional poles and lights.

Next I used the editor to Edit Scenario that I had just created a few minutes prior. I added a few new entities that I wanted in an updated blueprint. But when I went to select my updated design with the BP editor, the selection cursor only selects the new entities I just added. Those I added before the save are ignored, as if they are decoratives. The same effect happens if I try to select with Ctrl-C or Ctrl-X, only the post-saved entities are selected. I have restarted several times and created new saves with additional entities. In all cases, the miners and related entities I placed before the first save can never be selected, only those after the initial re-load of that save.

I also tried to recreate by running a new scenario in the editor, but I can't recreate this failure to select entities in the new save.

I'm running the latest 2.1 experimental build.

edit: here's a screenshot:

Screenshot 2026-07-14 160517.png (2.61 MiB) Viewed 59 times

[robot256]

The editor mode won't select the entities I placed before I saved the editor session. Please tell me what I'm doing wrong, or if I broke it, how so I don't break it again.

I created a new editor session with all default game settings. After it loaded, I cleared all entities, changed to lab tiles, and then stamped a 250 square of copper. I created an array of miners and 3 similar blueprints in a new blueprint book. I ran the simulation for a bit confirming that the belts were complete, etc. Then I Save As a new file, then exited. I loaded up my current game and stamped a few copies of the BP, and then I decided to add some additional poles and lights.

Next I used the editor to Edit Scenario that I had just created a few minutes prior. I added a few new entities that I wanted in an updated blueprint. But when I went to select my updated design with the BP editor, the selection cursor only selects the new entities I just added. Those I added before the save are ignored, as if they are decoratives. The same effect happens if I try to select with Ctrl-C or Ctrl-X, only the post-saved entities are selected. I have restarted several times and created new saves with additional entities. In all cases, the miners and related entities I placed before the first save can never be selected, only those after the initial re-load of that save.

I also tried to recreate by running a new scenario in the editor, but I can't recreate this failure to select entities in the new save.

I'm running the latest 2.1 experimental build.

edit: here's a screenshot:
Screenshot 2026-07-14 160517.png

Are the new entities you placed assigned to a different force from the old entities? It sounds like during either the first or second session, you forgot to change the editor force from "Auto (enemy)" to "player".

[Tyrannosapien]

Are the new entities you placed assigned to a different force from the old entities? It sounds like during either the first or second session, you forgot to change the editor force from "Auto (enemy)" to "player".

Thanks so much, that is the problem somehow. I'm not sure what I touched as I was clicking through those dialogs the first time. But now playing around with the force editor I can select all items again. I don't fully understand it, but hopefully I'll remember to keep hands off there