[2.0.11] Decider combinator condition becomes green when the condition isn't met

Post your bugs and problems so we can fix them.
Post Reply
Copy link
ElderAxe
Fast Inserter
Fast Inserter
Posts: 160
Joined: Thu May 18, 2017 8:04 am
Contact:
Contact ElderAxe

[2.0.11] Decider combinator condition becomes green when the condition isn't met

Post by ElderAxe »

weird logic.gif
weird logic.gif (1.03 MiB) Viewed 434 times
This logic doesn't work correctly. third option should be green when 1 signal equals zero. But it works on opposite case. It works when 1 is NOT zero.

This is the combinator:
10-28-2024, 22-55-36.png
10-28-2024, 22-55-36.png (449.45 KiB) Viewed 434 times
This is the blueprint for test:
Top
robot256
Smart Inserter
Smart Inserter
Posts: 1063
Joined: Sun Mar 17, 2019 1:52 am
Contact:
Contact robot256

Re: [2.0.11] Decider combinator condition becomes green when the condition isn't met

Post by robot256 »

Replicated on 2.0.21, but probably not a bug. This is the result of the time delay present in the drawing of the condition highlight effect, which seems to update after the signal is stable for one second. They are updated at a slower rate than the signals themselves to avoid unnecessary flashing. When I told the train (using legendary nuclear fuel) to stop and wait for a while rather than go in a continuous circuit, the '1' signal became 0 and became correctly highlighted. It just so happened that the train running continuously made a loop every two seconds, so it looked like it was always opposite of what it should be when actually it was phase-lagging.
Untitled.png
Untitled.png (2.31 MiB) Viewed 373 times
Top
ElderAxe
Fast Inserter
Fast Inserter
Posts: 160
Joined: Thu May 18, 2017 8:04 am
Contact:
Contact ElderAxe

Re: [2.0.11] Decider combinator condition becomes green when the condition isn't met

Post by ElderAxe »

I have some crazy combinators which changes conditions a lot faster than this and never had this issue with them. If they can correctly update their status, this combinator should as well. It has a lot more time to update between status changes.

I played with editor by pausing time. It shows the correct color based on the condition when you hover the signals on input section. (Which triggers refreshing the backgrounds to show the status for that specific signal)
Also when you close the combinator modal and open it again, then the coloring is correct until the next cycle.

But if you don't do anything it stays on the wrong color. Green for false, Default gray for true.
Top
robot256
Smart Inserter
Smart Inserter
Posts: 1063
Joined: Sun Mar 17, 2019 1:52 am
Contact:
Contact robot256

Re: [2.0.11] Decider combinator condition becomes green when the condition isn't met

Post by robot256 »

The highlighting updates immediately if the output state of the condition changes. It appears to update after 1 second if the output does not change as a result (because other conditions are still not met).

It's important to be clear that it's not *opposite* the state it should be, it's *delayed* by the same length of time that the signal is changing in. Put coal in the locomotive and give it a longer track, and you will see what I mean.
Top
ElderAxe
Fast Inserter
Fast Inserter
Posts: 160
Joined: Thu May 18, 2017 8:04 am
Contact:
Contact ElderAxe

Re: [2.0.11] Decider combinator condition becomes green when the condition isn't met

Post by ElderAxe »

Yeah. You're right. The behavior makes sense with slower train. It's not a bug but an inconvenience.

Since it only needs to be updated when the player is watching this modal, I would expect to see the change sooner (hopefully at the same tick). It updates the input value shown on the condition. So it makes sense that the condition is checked and updated accordingly as well.
Top
Waity5
Burner Inserter
Burner Inserter
Posts: 14
Joined: Fri Jan 05, 2018 8:10 pm
Contact:
Contact Waity5

Re: [2.0.11] Decider combinator condition becomes green when the condition isn't met

Post by Waity5 »

I found the same issue in 2.0.21, the combi is being blinked on for 1 tick every 100 ticks. Interacting with it in any way updates it
Attachments
2024-11-25 16-13-38.mp4
(4.64 MiB) Downloaded 13 times
Top
Muche
Filter Inserter
Filter Inserter
Posts: 714
Joined: Fri Jun 02, 2017 6:20 pm
Contact:
Contact Muche

Re: [2.0.11] Decider combinator condition becomes green when the condition isn't met

Post by Muche »

Ref 125064 Decider combinator menu visual bug when no output.
Top
Post Reply

Return to “Bug Reports”