[kovarex] [2.0.12] Blueprint Parameter not updating Inserter Stack Size Signal

[DodgeX]

It seems, that blueprint parameters do not correctly set/update the "Control signal" for "Set stack size" in inserter BP.

Here is a minimal setup, a inserter with used iron bacteria for filter and enable circuit, as well as stack size signal.

10-30-2024, 18-28-54.png (275.5 KiB) Viewed 1688 times

I created a BP that replaces the bacteria with parameter 0.

10-30-2024, 18-29-35.png (1.9 MiB) Viewed 1688 times

After placing the BP and picking nutritions in this case, the filter and enable conditions are updated, the signal is not.

10-30-2024, 18-30-26.png (302.38 KiB) Viewed 1688 times

When trying to create a new parametrized BP from the nutrition inserter it does not show the bacteria even it is still used as control signal

10-30-2024, 18-31-40.png (462.67 KiB) Viewed 1688 times

The BP String (with paramter)

Code: Select all

0eNqNkmFPgzAQhv/LfS7LimMLJPpHloUUOPViabG007nw372CI26i8QOEXnvP+/Jez1DpgJ0j46E4A9XW9FDsz9DTk1E61oxqEQqogn5JyPToPDoYBJBp8B0KOYiF0y02FNoENdbeUZ10VuO3pnQ4CEDjyRNOeuPiVJrQVowvpPiTJKCzPTdbEzUZmNzt5CoTcOLWfLfKhujqhpmK5X9ZgG3zK5iAhhzrj0ckczgm76wuK3xWR7IuNtbk6kC+RKMqjQ0U3gUUc5lbmlnkkVzvyx+pdcrxB3tK1jGsOAyv4mRkXLRx20cxeBi3v8g98uNV/cLAD7zoTpWLUTJdWBAkZ01SqZolSQGHxs40L6aZXCYslvwJeA1Kc75cN9a1zL0xeQ9xyqHHcoZGa7H4xnFGjb0UUqRCHrg2wydxf+pGhw1j+fWLeHIV6z8cRXXy2MZbMN98AUeWHSHZNs03eZ5t0vVut9kOwye6nhDN

[Whaim]

I thought I was going crazy! I'm having the same issue. No prompt appears for the inserter parameter to input a value, however if you put a formula in the field, that does work.

[hsugozen]

I'm not sure this is related or different; but I'm seeing an issue where when I enter a formula with the assembler (p0_s) - it sets the stack size correctly.

But when I set it with the biochamber, it doesn't appear to set correctly.

I've attached 4 screenshots. 2 of the parameters/formula, 2 of the results once placed down.

In the biochamber case, it just selects the multiplier; in the assembler case, it properly selects the stack size as a multiplier.

edit: as an update, I got it to work correctly when I blueprinted it horizontally rather than vertically.. not sure why that fixed it but it did?

[kovarex]

Hello, thanks for the report.
I added the stack size value to be configurable by the blueprint parameters system for the next release.

[macdjord]

@koravex: Which release is this supposed to be fixed in? Because it's still broken in 2.0.20.