Plz change how Train signal works...

[PanTobi]

TL:DR
-> Change where You place Train Signals, instead of placing them OUTSIDE rails, make them INSIDE rails...
so we can place Signals anywhere we need to...

s1.png (3.99 KiB) Viewed 4047 times

Current train signals are annoying AF... srsl...
I can't build small and compact Railway network because of those stu*$ f&$*...

It must be always ONE LITTLE TINY LIGHT MISSING THAT RUINS EVERYTHING...

So plz... change how Train Signals works, how u place them...

Instead of placing Rail Signals on SIDE of the rail... plz make it so we can place rail signal INSIDE rails...
so we have no limits on where and how many Signals we put... for last 90 min im trying to build my new Design for rails

And as always signals don't want to Coop...


Here is example... if i could place ONE LIGHT right there in middle where Left ways cross... everything could work 100% perfect...
but because i can't place light here... Trains going left will block trains going right etc.

( Ignore that im not using Chain Signals, i just always use Regualr signals to split rails into segments and then i replace Signal with Chains )

SS

Desktop 2021-07-20 14-37-49-960.png (1.88 MiB) Viewed 4047 times

4 of 5 of my Rails Designs are going to trash just because of "YOU CAN"T PUT SIGNAL HERE"...

[boskid]

No.

- It would not be clear which way they bind so they would basically turn into bidirectional signals everywhere.
- They could be placed on a position where a metal of overlapping rail is making trains able to ride over a signal which would be ugly.

I think it should be possible to change rail signal collision mask to one that does not collide with rails. Only requirement here is for rail signals to collde with any other rail signal or rail chain signal entity.

[vjbone]

No.

- It would not be clear which way they bind so they would basically turn into bidirectional signals everywhere.
- They could be placed on a position where a metal of overlapping rail is making trains able to ride over a signal which would be ugly.

I think it should be possible to change rail signal collision mask to one that does not collide with rails. Only requirement here is for rail signals to collde with any other rail signal or rail chain signal entity.

1 rotate signal with R key
2 like this? https://www.trains.com/wp-content/uploa ... signal.jpg

[PanTobi]

No.

- It would not be clear which way they bind so they would basically turn into bidirectional signals everywhere.
- They could be placed on a position where a metal of overlapping rail is making trains able to ride over a signal which would be ugly.

I think it should be possible to change rail signal collision mask to one that does not collide with rails. Only requirement here is for rail signals to collde with any other rail signal or rail chain signal entity.

Option 1: Add Signals on left / right side but inside Rais?
Option 2: Add Signals with Arrow that point direction???

s1.png (5.96 KiB) Viewed 4020 times

[PanTobi]

2 like this? https://www.trains.com/wp-content/uploa ... signal.jpg

YES !!!

SS

absolute_signal.jpg (17.89 KiB) Viewed 4019 times

[Koub]

When facing the same issue as you did, the answer I found is that I tried to build too small. Space is virtually infinite, wanting to cram everything is as little space as possible (or in less space than possible) is a puzzle on its own, but I don't find it entertaining past a certain point.
If you scale your intersections 2x bigger, you'll have excess space to fit your signals.

[vjbone]

I think TS its more like mod request
"compact train signals"

[ssilk]

If you need to make it so small, I often rebuild everything. The destruction tool is your friend. I have a filter for rails/signals . In most cases I find ways to build, what’s needed.

The general rule (I’m the same opinion as Koub): you make it too small. Double everything and you’ll have no problems.

And what’s much more annoying is, that you can’t build signals in curves. It is so irritating, you need a lot of experience to plan ahead that to make fast and save crossings.

I think it should be possible to change rail signal collision mask to one that does not collide with rails. Only requirement here is for rail signals to collde with any other rail signal or rail chain signal entity.

Does that mean you can build a signal, even if there is rail?

I think TS its more like mod request
"compact train signals"

Not sure, if that does help. I mean, the placing of signals feels a bit clumsy from beginning, because you can’t place signals everywhere. It is a kind of puzzle from beginning. But if you just won’t puzzle then make it big.

[vulduv]

TL:DR

Allow Railway signals to be placed between rails to remove unneeded gameplay differences between RHD railways and LHD railways.

What?

Remove placement collision between railway signals and rails to allow for signals to be placed between the rails themselves. Except on junctions obviously.

Why should this be changed?

Which side trains should drive on is considered to be up to personal preference by most players. Yet railway signals (Which are always on the right side relative to the driving direction) collide with rails, making some designs impossible when using LHD or RHD.
Allowing railway signals and rails to "occupy" the same space would make both driving directions completely equal gameplay wise.
It would also allow for tighter designs, which could be fun.

Visual changes

The original models would have to be retweaked to better fit their new placement, as the current sprites are too large to fit between the rails.
And the placement icons that show up when holding railway signals would have to be altered.

Implementation

Very little would have to change with how players place, remove and interact with the railway signals. They would just get more choice.
As for the code, i have no idea how that would work. As i'm not a modder.
Maybe a modder will make a QOL mod using this suggestion? If someone does turn this into a mod, please link it below!

[Koub]

[Koub] Merged into older thread with the same suggestion. Also, highly unlikely this will be implemented one day.

[ssilk]

These are one of those things, that are deep frozen into the game engine.

It would be much more likely to change the whole train system, because it has many small issues.