Advanced Circuits production

HeilTec · Post by **HeilTec** » Tue Jul 15, 2014 2:37 pm

Advanced Circuits

Most of what is needed for a fairly fast production of advanced circuits

starxplor · Post by **starxplor** » Tue Jul 15, 2014 9:37 pm

Putting cables on a belt doesn't slow this way down? I long ago gave up trying that because it is just so slow without inserter bonus.
Nice and compact though, if needed in tight spaces.

Post by **ssilk** » Wed Jul 16, 2014 3:42 am

The most stuff is needed by the el. circuits, which are handled with inserters. The advanced circuits need only 4 wires every 8 seconds, which are no prob to handle with belts.
But I would not mix both productions. They are independent, for example a fourth wire assembly is needed only for the adv. circuits, currently unbalanced...

DaveMcW · Post by **DaveMcW** » Wed Jul 16, 2014 4:16 am

starxplor wrote:Putting cables on a belt doesn't slow this way down? I long ago gave up trying that because it is just so slow without inserter bonus.
Nice and compact though, if needed in tight spaces.

Advanced circuits need circuits, plastic, and cables in a 1:1:2 ratio. This fits perfectly with a circuit/plastic belt and a cable/cable belt. The 8-second production timer gives you plenty of time to load everything.

: advanced_circuits2.jpg (322.25 KiB) Viewed 14782 times

But if you're going for a compact design, belts take too much space.

: advanced_circuits.jpg (176.96 KiB) Viewed 14732 times

Post by **ssilk** » Wed Jul 16, 2014 9:34 am

I really need to make more with the wagon.

Neotix · Post by **Neotix** » Wed Jul 16, 2014 10:02 am

Design with wagon is fine but have one problem. Absolutely zero control over production and wagon can be easily flooded by one material and all will stop.

HeilTec · Post by **HeilTec** » Wed Jul 16, 2014 1:09 pm

Neotix wrote:Design with wagon is fine but have one problem. Absolutely zero control over production and wagon can be easily flooded by one material and all will stop.

Would some filtered slots in the wagon not take care of that problem?

I will try some wagon set-up's for sure.

Redominus · Post by **Redominus** » Wed Jul 16, 2014 2:59 pm

Wagon setup https://forums.factorio.com/forum/vie ... 662#p35305
Without a shared wire buffer sometimes one of the wire inserters from the middle assembler keeps filling only one of the circuit asembler while the other inserter can't catch up.

MisterSpock · Post by **MisterSpock** » Thu Jul 17, 2014 9:08 pm

This is for Modules.
The ratio is for productivity modules.
If u left enough room, Speedy Bacon is very effective.

Lee_newsum · Post by **Lee_newsum** » Fri Jul 18, 2014 10:01 am

what do you think of my way of doing it?

sonic · Post by **sonic** » Fri Jul 18, 2014 2:35 pm

Are you deliberately overproducing green circuits?

Lee_newsum · Post by **Lee_newsum** » Fri Jul 18, 2014 8:24 pm

sonic wrote:Are you deliberately overproducing green circuits?

Yes that is my Electronic circuit and Advanced circuit system. I have 2 of them and thinking of a 3nd one.
my map https://forums.factorio.com/forum/vie ... f=8&t=4710

sonic · Post by **sonic** » Fri Jul 18, 2014 9:15 pm

Cool, I figured as much with the active provider chest taking in green circuits but wasn't sure.

I like the idea of a square design; if you decide to supply some of the materials via train or belt, you can inject them from any direction.

Factorio Forums

Advanced Circuits production

Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production

Re: Advanced Circuits production