If a tank has less then 1 fluid but more then 0 (ex: 0.3 fluid) then it will not output a signal on a circuit network despite containing fluid
Recreating bug:
1) Placed blueprint 1 and waited a bit for it to stop moving liquid
2) Mouse over center tank and observe that there is liquid in it
3) Mouse over substation and note that the red signal is the only signal there
I expected it to not output 0 unless the tank is empty
Posable fix:
round up instead of down when dealing with fractional fluid amounts
Blueprint 1:
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
[1.0.0] tanks with fluids not giving a signal
-
- Inserter
- Posts: 40
- Joined: Sat Dec 14, 2019 3:26 am
- Contact:
[1.0.0] tanks with fluids not giving a signal
Last edited by -DeadlyKitten on Tue Oct 27, 2020 1:58 am, edited 1 time in total.
Re: [1.0.0] tanks with fluids not giving a signal
When offloading fluids from trains, try to offload into a buffer tank and have that pumped out to your factory.
A fluid wagon and tank both hold 25k units, so as long as the buffer tank is empty before offload, the fluid wagon will be guaranteed to be emptied during offload. If there are pipes between the offloading pump and your factory, and there is no pump to empty that pipe, then there may always be a residual amount. Using a tank allows you to monitor the exact amount in that part of the system
The thread @Loewchen links to, is rather old, and fluid handling has changed a little for the better since then.
A fluid wagon and tank both hold 25k units, so as long as the buffer tank is empty before offload, the fluid wagon will be guaranteed to be emptied during offload. If there are pipes between the offloading pump and your factory, and there is no pump to empty that pipe, then there may always be a residual amount. Using a tank allows you to monitor the exact amount in that part of the system
The thread @Loewchen links to, is rather old, and fluid handling has changed a little for the better since then.
-
- Inserter
- Posts: 40
- Joined: Sat Dec 14, 2019 3:26 am
- Contact:
Re: [1.0.0] tanks with fluids not giving a signal
see also: viewtopic.php?f=23&t=86041
I am asking for this anyway because without either this or with viewtopic.php?f=7&t=90745 multi fluid systems are nearly impossible to use, it is most likely a simple fix that could open a whole new area of interesting design.
I am asking for this anyway because without either this or with viewtopic.php?f=7&t=90745 multi fluid systems are nearly impossible to use, it is most likely a simple fix that could open a whole new area of interesting design.
-
- Inserter
- Posts: 40
- Joined: Sat Dec 14, 2019 3:26 am
- Contact:
Re: [1.0.0] tanks with fluids not giving a signal
my usage is not to due with trains, i am trying to make a compact advanced oil processing