well even with productivity i dont think you make overal more cages since you lose a lot of cages when you grow the animals

magals wrote: ↑

Fri Feb 21, 2020 1:55 pm

wtf why so long time craft manure?
recipe auog-manure-2

2 min video https://www.youtube.com/watch?v=jgkuFRm98Eo

PY is right you forgot to add the animal-module inside the building ! it gives a +3500% speed boost i think

I know that there are like 15-20 animals out there.And i know there are certain products that are 1 animal exclusives. BUT what is each supposed to be best at? manure bone meat skin guts brains that is the main question , i cant figure out what were supposed to be the best say 3-5 for each category

i updated the power calculator

without pyAL blood is in excess and i was voiding all my excess blood also fiberboard is expensive so fertilizer was used in my base as little as i could As for me i'm not using fertilizer for raw fiber its not imortant for it But fertilizer very very important for dimethylsulfide and methanesulfio...

without pyAL blood is in excess and i was voiding all my excess blood
also fiberboard is expensive so fertilizer was used in my base as little as i could

pyanodon wrote: ↑

Fri Feb 07, 2020 11:13 am

pyAL is big and its hard. If youre expecting something easy or dont get the mechanica etc, i reccomend dont play it.

WE LIKE YOUR MODS BECAUSE THEY ARE HARD.

but still doable , also the streams are hyper ing use way to much

For me, to get 100 molten nexelit in the following ways take the following amounts of high grade nexelit: Melting reduced: 15 high grade. Melting high grade: 5.9 high grade Melting sintered, where the thing that you sintered was reduced nexelit: 4.5 high grade Melting sintered, where the thing that...

not again

not sure if i should look into it with pyAL in the next weeks or so

BUT if py tells me to look into it and fix it i would .

maybe i should do another run down the chain for all ores ?

LOL

use tanks to easy the curves. i am useing them in the case of the 1 2 3k it is the variable temperature that is to blame , anyway i managed to stabilize the power made at 10 750 MW the problem is that when the 3k one inserts steam you can produce a lot of power fast but that runs out fast if you wa...

use tanks to easy the curves. i am useing them in the case of the 1 2 3k it is the variable temperature that is to blame , anyway i managed to stabilize the power made at 10 750 MW the problem is that when the 3k one inserts steam you can produce a lot of power fast but that runs out fast if you wa...

liwers wrote: ↑

Tue Jan 21, 2020 1:08 pm

A former translation participant from our community said, he received official email describes new translation requirement, which means 0.18 will be here soon..

So uh.. here comes the question: will pyAL be released before 0.18's on, or after it..?

meow..!

0.18 is here now

a maxed out reactor with antimatter can make up to 159 420 MW
39 855 MW on a non module one

I have been testing fusion setups for while and here is what i found : the power output is very unstable +-30% so it requires a thing that limits the power it can output in order to give constant power, i used some fast discharge accumulators but that had a disadvantage : it means that fusion power ...

yes apparently that was a great nerf that skipped my eye
a X2 one now lead might be in top 3 most used ores
Fe Cu Sn Ni (Pb ore)

lets start form the begining then : 1 at some point you can sort 1 lead concentrate(i think ) into 1 high grade Ag/Pb (one of each) , here the chain splits and you can get both at the same time 2 i know my Ag and Pb demand in my base 3 Ag is much more needed then Pb 4 i set up the chain up to then e...

BlueTemplar wrote: ↑

Fri Jan 17, 2020 10:06 pm

Hmm, is the Ni chain that instead consumes Al that much worse ?

Ni is not bad but u simply need tons of it the Al cost is low compared to what you get + you get Al pulp 2 so u kinda can loop it back

Higher Al tiers also make a small amount of the precious Vanadium as a byproduct, right ? I can make vandaium with normal way My questiuon is where to use these big counts of aluminum plates, and i think that very very serious question 1 build Ni-Al setups close to each other and make use of the Al...

Why to void intermediate lead products? Can't fully understood u PA will require toooooooooo any energy and i need many molybdenum ore? its okey with nickel ore i can get it from tar and its all good with ceramics and ash and lubricant since if you dont void them lead will back up and after that Ag...