[Kovarex] [2.0.34] Smart belt dragging over belt curve fails
Posted: Thu Feb 06, 2025 11:47 pm
I have come across some more smart belt bugs.
Since there are currently quite some bugs reports concerning smart belts, I was wondering what is currently the best way I should report those bugs:
- file one new report with all "new" bugs I can find (like I did here)
- file a new report for each different bug (that would mean 5 reports instead of this one)
- append to existing reports (like the 2 I mentioned in this report)
I would be glad to know what helps you the most!
Now to the actual report:
In each picture, the top row is the layout of belts before I drag a belt between the loaders.
I then copied this setup four more times and dragged a belt in the height of the loader. Each time, I would expect one continuous new belt (with undergrounds where necessary) while all belts placed before remain the same. A working example of this can be seen in Case 1, last row.
Each of those rows has a different orientation and direction of the belt drag. The orientation of the belt is the same as the orientation of the loader in the row and I start the drag next to the loader. That means:
The first row is after I dragged right-facing belt from left to right.
The second row is after I dragged right-facing belt from right to left.
The third row is after I dragged left-facing belt from right to left.
The fourth row is after I dragged left-facing belt from left to right.
The save file is attached.
Case 1:
1st and 4th row as expected, 2n and 3rd row broken
Case 2, very similar to Case 1:
1st and 4th row as expected, 2n and 3rd row broken
Case 3, note that I drag with red belt,
all rows broken
Case 4, similar to 632657 case 5 but a bit more complete:
1st and 4th row as expected, 2nd and 3rd row broken
Case 5, similar to 661871 (still broken but in a different way):
1st and 4th row as expected, 2nd and 3rd row broken
Since there are currently quite some bugs reports concerning smart belts, I was wondering what is currently the best way I should report those bugs:
- file one new report with all "new" bugs I can find (like I did here)
- file a new report for each different bug (that would mean 5 reports instead of this one)
- append to existing reports (like the 2 I mentioned in this report)
I would be glad to know what helps you the most!
Now to the actual report:
In each picture, the top row is the layout of belts before I drag a belt between the loaders.
I then copied this setup four more times and dragged a belt in the height of the loader. Each time, I would expect one continuous new belt (with undergrounds where necessary) while all belts placed before remain the same. A working example of this can be seen in Case 1, last row.
Each of those rows has a different orientation and direction of the belt drag. The orientation of the belt is the same as the orientation of the loader in the row and I start the drag next to the loader. That means:
The first row is after I dragged right-facing belt from left to right.
The second row is after I dragged right-facing belt from right to left.
The third row is after I dragged left-facing belt from right to left.
The fourth row is after I dragged left-facing belt from left to right.
The save file is attached.
Case 1:
1st and 4th row as expected, 2n and 3rd row broken
- 1.PNG (86.78 KiB) Viewed 2991 times
1st and 4th row as expected, 2n and 3rd row broken
- 2.PNG (103.67 KiB) Viewed 2991 times
all rows broken
- 3.PNG (60.29 KiB) Viewed 2991 times
1st and 4th row as expected, 2nd and 3rd row broken
- 4.PNG (52.03 KiB) Viewed 2991 times
1st and 4th row as expected, 2nd and 3rd row broken
- 5.PNG (95.37 KiB) Viewed 2991 times