Factorio Forums

LyrickCZE wrote:Yea, I was thinking about that too... Now that I know I'm not alone, I made it happen.
Had to change the yellow dirt as well.

Original vs. new

It's not a mod, you need to unpack the .zip and overwrite all 4 folders in the "...\Factorio\data\base\graphics\terrain"
So make sure to backup those folders before overwriting them.

Sand-and-Dirt_by_Lyr_v1.zip

keyboardhack wrote:

Marc90 wrote:I love this mod, great work!

But there might be something wrong with the yellow inserter:

pic

I'm using Factorio 0.12.26 and WaiTex 1.0.0 and a couple of other mods.

There is definetly something wrong with that inserter. I will i will make a new release today that will fix that.

orzelek wrote:

keyboardhack wrote:

Marc90 wrote:I love this mod, great work!

But there might be something wrong with the yellow inserter:

pic

I'm using Factorio 0.12.26 and WaiTex 1.0.0 and a couple of other mods.

There is definetly something wrong with that inserter. I will i will make a new release today that will fix that.

Anyone has ideas how to fix this one?
Or did I miss a release?

It's a bit annoying after you notice it

["%name%"] = 					{["enabled"] = false, ["requiredGB"] = 1},

bbgun06 wrote:The smart inserters are messed up also.
Fast and long look ok.

Thanks for your hard work, this is one of my favorite mods!

Speadge wrote:there is a problem with the treeSaplings mod that brings a trunk.png.

because of some code in the base-override

Code: Select all

--trees are a special case because there is so many files for them. Therefore they are checked here but only if they are of the type tree
if AllowChange("tree") then
	if AllowChange("tree", data.raw["tree"]["tree-01"].variations[1].leaves) then
		for k,trees in pairs(data.raw["tree"]) do
			if trees.variations then
				for k1, treeVariations in pairs(trees.variations) do
					OverrideSprite(treeVariations.leaves)
					local filename = treeVariations.trunk.filename
					filename = string.gsub(filename, ".png", "") -- not good to have it here... oh well
					filename = string.gsub(filename, "__base__", "__WaiTex__")
				
					AddStripes(treeVariations.trunk, nil, nil, 
					{
						{filename.."-1.png", 3, 1},
						{filename.."-2.png", 2, 1}
					})
				end
			end
		end
	end
end

it looks for a trunk-1 and trunk-2.png which is not provided by this mod.

Factorio2016 wrote:QUESTION:
And if I replace the original files in the game, then memory consumption will be much the same?
just curious

• fixed fast inserter
• fixed smart inserter
• fixed compatibility with modded trees
• updated checmical plant
• updated oil refinery
• updated player
• updated small pump
• updated stone wall
• updated storage tank

kingoftheinternet wrote: 1. WaiTex doesn't seem to cooperate with ExtraChests, despite the note in 0.8 that seems to say it should. Among other things, ExtraChests adds a consistent tinting scheme to the Bobmods levelled constructs (which AFAIK all use base textures) that indicate which level a construct is. I dunno which of you would have to change something to make these two mods cooperate, but there you have it.

Crusha wrote:Error:

http://prntscr.com/b0veu1

bbgun06 wrote:Thanks for the update. Since the game started comparing hashes of each mod before allowing multiplayer connections, it it no longer possible for one player to have the 1GB version while another has the full version. Have you thought of any ways around this?

keyboardhack wrote:Version 1.0.1

Crusha wrote:Error:

http://prntscr.com/b0veu1

I can't reproduce this so i assume the download was corrupted somehow. If downloading the mod again doesn't work then i would like a list of all the mods you use so i can test it.

Crusha wrote:

keyboardhack wrote:Version 1.0.1

Crusha wrote:Error:

http://prntscr.com/b0veu1

I can't reproduce this so i assume the download was corrupted somehow. If downloading the mod again doesn't work then i would like a list of all the mods you use so i can test it.

I have tested all my mods. The Mod "MAIN-DyTech-Power_1.9.9" produces the error.

function SteamHorizontalPictures(Scale, Tint)

function SteamVerticalPictures(Scale, Tint)